AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateTrusted Furnace Repair for Enterprise Homeowners
A furnace that quits in the middle of a cold snap is the kind of problem that gets worse the longer it sits. We’re an HVAC-only company, and AC Repair Enterprise sends heating specialists who diagnose the equipment you actually have instead of guessing at it. Our technicians have up to 12 years of experience and are trained on nine leading brands, so a Carrier, Trane, Lennox, or American Standard furnace gets looked at by someone who knows where that model tends to fail. We work on the brand you already have, and we tell you straight whether a repair makes sense or a replacement does. Furnace repair in Enterprise typically runs $150-$700, set per job by a free written estimate. Call (833) 632-6348 and we’ll get a dispatch moving.
Furnace Maintenance
Furnace Maintenance is the scheduled inspection and cleaning that keeps a heating system running safely and efficiently between seasons, and it’s the single best defense against a mid-winter breakdown. If your furnace hasn’t been looked at in a year or more, or you’ve noticed it cycling oddly, a maintenance visit makes sense now rather than later. We check the burners, the heat exchanger, the blower, the flue, and the ignition system, then hand you a written report of what we found. Maintenance visits in Enterprise typically run $80-$200 depending on the scope, and the written estimate sets the final price. Our technicians aren’t paid on what they sell, so the report reflects the equipment, not a sales target.
What a Maintenance Visit Covers
We inspect the heat exchanger for cracks, test the ignition and flame sensor, clean or replace the filter, check the blower motor, and confirm the flue is drafting properly. You get a plain-language rundown of anything that needs attention and what it would cost to fix.
When to Schedule One
The right time is before the heating season starts, not after the system has already failed. If it’s been more than a year since the last inspection, schedule one. Annual attention catches small issues while they’re still cheap to repair.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Heat Pump Repair
Heat Pump Repair addresses the heating side of a heat pump system when it stops warming the home or switches into defrost mode at the wrong times. Desert nights around Enterprise get cold enough that a struggling heat pump becomes obvious fast, and the symptoms often point to a reversing valve, backup heat strip, or refrigerant charge problem rather than the compressor itself. We diagnose the actual fault with gauges and electrical testing before recommending anything, then give you a repair-first answer. Heat pump repair in Enterprise typically ranges from $150-$700 depending on the component, with the written estimate setting the final price. Call (833) 632-6348.
Common Heat Pump Faults
Reversing valves that stick, defrost boards that fail, and low refrigerant from a slow leak are the three we see most often. Each shows up differently, which is why electrical testing and pressure readings matter before parts get ordered.
Repair or Replace the Unit
Heat pumps are worth repairing when the compressor and coil are healthy and the fault is a valve, board, or sensor. When the compressor is failing and the system is older, replacement often costs less over time. We’ll show you the numbers both ways.
Heating Repair
Heating Repair covers any fault in a home’s heating equipment where the system won’t produce heat, produces uneven heat, or shuts off before reaching temperature. It’s what you call when the thermostat says it should be warm and the rooms say otherwise, and the cause could be anything from a failed igniter to a blower that’s drawing too many amps. We start with a full diagnostic rather than a parts swap, which keeps you from paying twice for the same problem. Heating repair in Enterprise typically costs $150-$700 depending on what’s failed, and the written estimate sets the final price. Fast dispatch runs 7am-7pm, and we answer 24/7 for scheduling.
Diagnostic Testing We Run
We measure amp draw on the blower, test the igniter and flame sensor with a multimeter, verify gas pressure at the manifold, and check temperature rise across the heat exchanger. Those readings separate a worn part from a real safety issue.
Uneven Heat Through the House
Some rooms warm and others don’t, which usually points to airflow or duct issues rather than the furnace itself. We trace static pressure and check register output to find where the heat is going instead of guessing at a bigger unit.
Boiler Repair
Boiler Repair handles the faults that take a hydronic heating system down: no hot water, low pressure, a pilot or ignition lockout, or leaks at the circulator and relief valve. Boilers are less common in Enterprise homes than forced-air furnaces, but when they fail they fail quietly and take the whole house’s heat with them. We check pressure, temperature, and the safety controls before touching anything, and we replace components rather than talking you into a new boiler when repair is viable. Boiler repair in Enterprise typically runs $150-$700 depending on the part, with the written estimate setting the final price. Call (833) 632-6348 to schedule.
Pressure and Safety Controls
A boiler running outside its rated pressure is a safety concern, not just a comfort one. We test the relief valve, expansion tank, and low-water cutoff, and we won’t leave a boiler running if those controls are compromised.
Circulator and Zone Problems
Cold zones or a boiler that fires but doesn’t heat the house usually trace to a circulator pump, zone valve, or air in the loop. We isolate each zone to find where circulation stops.
Gas Furnace Repair
Gas Furnace Repair covers the ignition, gas valve, burners, and venting on a gas-fired furnace, which are the parts homeowners should never troubleshoot themselves. Gas lines and combustion are genuinely dangerous to work on, so a furnace that smells like gas, has a yellow flame where it should be blue, or shows soot around the burners needs a trained technician, not a DIY fix. If you smell gas, leave the house and call your gas utility first. We test gas pressure, check for leaks, and inspect the heat exchanger with a camera before we sign off on a repair. Gas furnace repair in Enterprise typically runs $150-$700, set by the written estimate. Call (833) 632-6348.
Combustion and Venting Checks
A furnace that vents into a clogged flue can push carbon monoxide back into the home. We confirm draft, check the flue for blockages, and test combustion with a gas analyzer so the repair doesn’t just restore heat but restores safe heat.
Heat Exchanger Inspection
A cracked heat exchanger is the most serious furnace fault there is, and it doesn’t always show up as an obvious symptom. We inspect it with a camera and pressure test before calling the system safe to run.
Furnace Tune Up
Furnace Tune Up is the flat-price inspection that cleans, adjusts, and tests the whole heating system so it starts the season in good working order. It makes sense every year before the heating season, and it also makes sense after a repair to confirm the fix is complete. We clean the burners, adjust the flame, replace the filter, verify temperature rise, and test the safety switches. You get a written report of what we found, and our technicians aren’t paid on what they sell, so the report stays honest. Furnace tune-ups in Enterprise typically run $80-$200, and the written estimate sets the final price. Same-day scheduling is often available.
What Gets Cleaned and Adjusted
Burners get brushed, the flame sensor is cleaned or replaced, the blower wheel gets cleared, and the filter is swapped. Small adjustments to gas pressure and airflow can make a real difference on an older unit.
Tune Up After a Repair
Follow-up tune-ups confirm the repaired part is working with the rest of the system. It’s a way to catch a secondary fault before the weather turns it into a second repair.
Emergency Furnace Repair
Emergency Furnace Repair is for heat that’s failed when the temperature outside makes waiting until tomorrow a genuine health concern, especially for children, older adults, or anyone with medical equipment at home. Those calls get prioritized for same-day service, and we run through the likely fault over the phone so the first visit is aimed at the right component. We answer 24/7, and fast dispatch runs 7am-7pm, Sunday through Friday; a call outside dispatch hours is booked into the next opening. Emergency furnace repair in Enterprise typically runs $150-$700, set per job by the written estimate, with no surcharge for urgency. Call (833) 632-6348.
What Counts as an Emergency
No heat in freezing weather, a gas smell, soot, or a CO alarm is an emergency, not a wait-and-see. If you smell gas, leave the house and call your gas utility, then call us once you’re safe.
What to Do While You Wait
Close off unused rooms, run the fireplace if you have one with a proper flue, and keep the indoor temperature above freezing to protect pipes. Don’t restart a furnace that’s tripping the breaker or showing a fault code you can’t read.
Brands We Service
We service American Standard furnaces and know the ignition and control board faults that model line tends to develop. The same goes for Carrier equipment, where the heat exchanger and inducer motor are the components we check first on a no-heat call. Trane gas furnaces have their own control sequencing quirks, and a technician who hasn’t worked on them can waste a service call chasing a fault that’s actually normal behavior.
Lennox equipment calls for attention to its venting and pressure switch behavior, and we know where those systems wear out. We don’t stock OEM parts or claim to be a dealer, but we do know how to diagnose each of these brands correctly instead of treating them all alike. Whether you have American Standard, Carrier, Trane, Lennox, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- No heat and the thermostat is calling. If the thermostat is set and the system isn’t responding, the fault is usually an igniter, flame sensor, or control board. Those aren’t parts to swap at home.
- A gas smell near the furnace. Any gas odor is a stop-and-call situation. Leave the house, call your gas utility, and let a trained technician find the leak.
- Yellow flame instead of blue. A blue flame means clean combustion. A yellow or orange flame suggests incomplete burning, which can mean carbon monoxide is being produced and isn’t venting properly.
- Repeated shutoffs on the same cycle. A furnace that starts, runs a few minutes, and shuts off is usually tripping a safety limit. That’s the system protecting itself, and it needs diagnosis, not a reset.
- Carbon monoxide alarm going off. Get everyone outside and call the fire department or your gas utility. Don’t re-enter to investigate the furnace yourself.
Our Process, Step by Step
- 1
Phone diagnosis. We ask what the furnace is doing and what the thermostat shows before anyone drives, so the first visit is aimed correctly.
- 2
On-site inspection. We test the equipment with a multimeter, gas analyzer, and camera so the diagnosis comes from readings rather than guesses.
- 3
Written estimate. You get a clear price for the repair, and a repair-vs-replace comparison if that’s the smarter conversation. The written estimate sets the final price.
- 4
Repair and test. The technician makes the repair and confirms the system runs through a full cycle, checking temperature rise, draft, and safety switches.
- 5
Report and follow-up. You get a summary of what was found and fixed, plus anything to watch for going forward.
How Much Does Furnace Repair Cost in Enterprise?
Furnace repair in Enterprise typically runs $150-$700, and the price depends on which part failed more than on the size of the house. A typical igniter or flame sensor replacement lands near the low end of that range, since the parts are simple and labor is short. A blower motor or control board replacement usually sits in the middle. A heat exchanger repair or a gas valve replacement sits at the high end, because those jobs involve more disassembly, more testing, and more safety verification before the furnace goes back into service. Heat pump and boiler faults follow the same pattern, with cost driven by the failed component.
What affects the price: the part in question, how accessible the furnace is, whether other components are worn enough that replacing them now makes sense, and whether a follow-up tune-up is needed. What doesn’t affect the price: the time of day or how urgent the call is. We don’t add an urgency surcharge.
How to avoid overpaying: get a written estimate that names the failed part before anyone touches the system, and ask for the repair-vs-replace comparison if the technician is nudging you toward a new unit. A repair-first company will show you the numbers.
What the free estimate includes: the diagnostic, the part identification, and a written price. The written estimate sets the final price. Call (833) 632-6348 to schedule.
Our Service Area Near Enterprise
We send technicians across the Valley, including Enterprise, Boulder City, Spring Valley, Paradise, Henderson, Sunrise Manor, Las Vegas, and North Las Vegas. Most addresses in Enterprise get same-day furnace repair scheduling, and outlying areas are booked into the next opening. Fast dispatch runs 7am-7pm, Sunday through Friday. If you’re not sure whether your address is covered, call and we’ll confirm before booking.
Serving Enterprise, NV – Our Local Coverage Area
We serve Enterprise and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Furnace Repair in Enterprise
Furnace repair is the diagnosis and correction of a fault that’s keeping a furnace from heating properly, safely, or at all. It covers ignition problems, failed blower motors, control boards, heat exchangers, venting issues, and gas-side faults. The goal is to fix the actual failed component rather than replace the whole system. Call (833) 632-6348 for a free estimate.
Most furnace repairs are done in a single visit and take one to three hours, depending on the part and how accessible the equipment is. Simple fixes like an igniter or flame sensor go faster; blower motors and heat exchangers take longer because the system needs to be tested through a full cycle afterward. If a part has to be ordered, we’ll tell you the timeline before you commit. Call (833) 632-6348 to schedule.
Furnace repair in Enterprise typically costs $150-$700, and the price depends on which component failed. Igniters and sensors land near the low end, blower motors and control boards sit in the middle, and heat exchanger or gas valve work sits at the high end. The written estimate sets the final price, and there’s no surcharge for same-day calls. Call (833) 632-6348 for an exact quote – estimates are free.
Yes, we service Carrier, Trane, Lennox, and American Standard equipment, along with five other major brands: Goodman, Rheem, York, Daikin, and Bryant. Our technicians are trained on nine leading brands, so they diagnose the equipment in your home rather than treating every system the same way. We work on the brand you already have instead of steering you toward a replacement. Call (833) 632-6348 to book a diagnostic.
Same-day furnace repair is often available in Enterprise, and emergency no-heat calls are prioritized. We answer 24/7, and fast dispatch runs 7am-7pm, Sunday through Friday; a call outside dispatch hours is booked into the next opening. We’re closed Saturday. Call (833) 632-6348 for an exact arrival window.
We stand behind the repairs we perform, and the written estimate spells out what’s covered on the parts and labor for your specific job. Ask us to walk through the warranty details before the work starts so there are no surprises. If something comes back after the repair, we want to know about it. Call (833) 632-6348 to discuss coverage.
Clear access to the furnace, the thermostat, and the breaker panel so the technician can reach the equipment without moving stored items. Note the thermostat setting, any fault code on the display, and whether the furnace is making any unusual sounds. Keep children and pets out of the work area. Have your system’s model number handy if you can find it. Call (833) 632-6348 if you have questions before the visit.
Schedule Your Furnace Repair Service in Enterprise Today
When your furnace stops, the fix starts with a call. Reach us at (833) 632-6348 for a free estimate, and we’ll tell you honestly whether the system needs a repair or a replacement. We answer 24/7, fast dispatch runs 7am-7pm, Sunday through Friday, and the written estimate sets the final price with no obligation. We work on the brand you already have.
Written by the team at AC Repair Enterprise.